Blog

November 2009 News: PT&P is Awarded the ISO Certificate
November 25, 2009

PT&P is Now ISO 9001:2008 Certified (11-23-2009)
Piping Technology & Products, Inc. is awarded the ISO 9001:2008 certificate by DNV Certification, a division of Det Norske Veritas (DNV), for the Manufacture of Hot and Cold Pipe Supports. This certificate proves that PT&P’s Quality Management System has been certified against the best practice standard and is compliant.

Iso 9001:2008

View ISO 9001:2008 Certificate

The latest version of standards, ISO 9001:2008 is created by the International Organization for Standardization (ISO), who set international requirements for Quality Management Systems. By conforming to the Quality Management System, Piping Technology & Products, Inc. demonstrates predictability of internal operations and the ability to meet customer requirements. While becoming certified, a company can identify the areas that are most critical to operations through management system audits. Once problem areas are identified, measured, managed and improved, customer satisfaction will rise, staff responsibility and motivation will also experience growth.

Read More

25-7/8″ Diameter High Temperature Supports for a Rush Job
November 17, 2009
25-7/8″ Diameter High Temperature Supports For A Rush Job
25-7/8″ Diameter High Temperature Supports for a Rush Job

PT&P fabricated hot shoes with an insulation thickness of 2 ½” and a pipe size of 20″. The supports are fabricated from carbon steel with a red oxide finish and calcium silicate insulation. They are capable of loads up to 3400 lb. and temperatures ranging from 40°F to 1200°F. PT&P completed delivery for this rush job within two weeks.

Want to learn more about hot shoes? Instantly watch a pre-insulated support webinar today!

Access-Our-Webinar-Archives

Read More

4″ to 14″ Diameter Spectacle Blinds for Process Piping
November 10, 2009
4″ To 14″ Diameter Spectacle Blinds For Process Piping
4″ to 14″ Diameter Spectacle Blinds for Process Piping

 

4″ To 14″ Diameter Spectacle Blinds For Process Piping
4″ to 14″ Diameter Spectacle Blinds for Process Piping

Sweco Fab, Inc., a division of PT&P, fabricated a variety of six spectacle blinds that will be used for selective line isolation. The spectacle blinds are fabricated from A516-70 carbon steel with sizes ranging from 4″ to 14″ diameter and per ASME B16.48 code. The function of a spectacle blind is to allow a line to be in either full shut-off mode or full flow mode, depending on which side is being utilized. Spectacle blinds are a lower cost alternative to double block and bleed valves where OSHA requires positive isolation of piping segments for safety reasons.

Want to learn more about spectacle blinds? View a webinar about Sweco Fab today!
Access-Our-Webinar-Archives

Read More

Hydraulic Snubber and 3-Bolt Clamp Assemblies for a Refinery Expansion Project
November 3, 2009
Hydraulic Snubber And 3-Bolt Clamp Assemblies
Hydraulic Snubber and 3-Bolt Clamp Assemblies (Item #2 & #3)
Hydraulic Snubber And 3-Bolt Clamp Assemblies For A Refinery Expansion Project
Hydraulic Snubber (Item #1)

Fronek Anchor/Darling Enterprises, Inc. and PT&P designed and fabricated hydraulic snubber and 3-bolt clamp assemblies for a refinery expansion project in Louisiana. A cycle test throughout the full stroke from zero to fully extended was performed prior to shipping.

Item #1: C-C: 61″, stroke: 12″, cylinder size: 5″ dia., max. load: 50,000 lb., 3-bolt clamp: A240 Gr. 304 SS, pipe size: 12″

Item #2: C-C: 71-7/8″, stoke: 6″, cylinder size: 4″ dia., max. load: 30,000 lb., -bolt clamp: A-36 carbon steel, pipe size: 16″

Item #3: C-C: 85-5/8″, stoke: 6″, cylinder size: 4″ dia., max. load: 30,000 lb., -bolt clamp: A-36 carbon steel, pipe size: 16″

Do you see a need for snubbers or clamps in your piping system? Get pricing today!
Request-A-Quote

Read More
Top